TOP 10 Best Diy Tube Amp Results at 10Bestify.com
Item specifics: Tubes: 5Z4P / 5U4C * 1 + 6N8P / 6H8C * 2 + 6P3P / 6L6GC * 2 Power supply: 300v * 2 6.3v 5v 3.15v * 2 Signal / Noise Ratio: 95dB Distortion: less than 1% at full power Frequency: 10HZ-70KHZ 3dB Output Power: 7W +7 W Voltage: 100V-240V Size: 290 * 170 * 150 mm Weight: 8KG Best Diy Tube Amp
Parameters: With original and new tubes 6n9p+EL34B Input Impedance: 100Kohm Output Impedance:4ohm 8ohm Signal to Noise Ratio: 89dB Input Sensitivity: 500--2000mV Input :110V/ 220V Output power:13w+13w (RMS) Frequeney responses: 20Hz--30KHz+/-1dB Supply Votage: all voltages are available 60Hz/50Hz Total Hamonic Distortion: less than 1%(1KHz) Tubes Included: 2pcs EL34B, 2pc 6N9P, 1pc 5Z3P Maximum input peak:500mW Dimension:350(W)*50(H)*170(D)mm Weight: 9.5kg With 2 new original BENNIC 0.33UF630V Capacitor, 2 ELNA 220UF/63V Resistor Notice: The loading resistor of this product is 4 ohm /8 ohm. Please do not change the value. Otherwise, the 6P3 loading resistance will be changed too. Please don't cut off the loading when it's working. If you want to connect this amplfier with a preamplifi... [Read More] Best Diy Tube Amp
Diagram:https://drive.google.com/open?id=1HnZELnau3EPR0Gk-wUPoxipQ0_PF7oalShipping date: This item will be shipped by UPS from China, which usually take 4~7 days to arrive. Parameters: Type: Single-Ended Class A Input Voltage: 110V-120V / 50-60Hz Output Power: 12W* 2 (ultra-linear connection) Frequency Response: 20Hz - 28KHz Output impedance: 4,8Ω SNR: 88dB Total Harmonic Distortion: ≤ 1% (1kHz) Input Sensitivity: 750MV Input impedance: 100KΩ (two input signals) Audio input: 2× Stereo L/R RCA Audio output: 1× Banana Speaker Jacks Dimensions(W × D × H): 310 × 268 × 165mm Weight: About 11Kg(You can see the quality from its heavy weight) Package includes: 1× full set of amp kit 1× power cord Best Diy Tube Amp
Description: This is a preamplifier + headphone amplifier that can be used with a post-amplifier or an active speaker, or it can be used with headphones. The sound of this board is warm, mellow, sweet and transparent, and full of music. It is a cost-effective preamplifier. Replaceable op amp and upgrade the tube, just plug it in the direction of the foot. Let you enjoy DIY fun! Specification: Material: acrylic Input port: audio input, power input Output port: 3.5MM headphone output, preamp output Size: 12.5 x 7.6 x 3.5cm / 4.9 x 3.0 x 1.4in (assembled size) Weight: approx. 259g Packing List: 1 x Acrylic Board 1 x 6J1-2 Tube Board Best Diy Tube Amp
Notice:Both 4Ω and 8Ω speakers can connect to the 8Ω and 0Ω posts of this amplifier. Specifications: Output power: 6.8W * 2 Frequency response: 20Hz-20KHz Input impedance: 100K ohms Output impedance: 4/8Ω SNR: 90db Input Sensitivity: 500mv-2000mv Harmonic distortion: 1% (1KHz) Tube: 5Z4P * 1 6H8C * 2 6P1 * 4 Operating voltage: 110V Weight: about 7 kg Size: 260mm * 215mm(including terminals and knobs 260mm) * 150mm (W*D*H) Package includes: Finished tube amplifier ×1 Power cable ×1 Best Diy Tube Amp
Technical parameters: Frequeney responses: 10Hz-100KHz (± 0dB), 10Hz-200KHz (± 0.2dB) RMS: 0.8W * 2 Power supply: AC 220V-240V or 110V Tubes used: 2pcs 6P6P, 2pcs 6J4, 1pc 653P Input: 4ways RCA jacks Output: 1way RCA jacks Supply votage: All Voltages are available 60Hz / 50Hz The machine output voltage of 12V, an enlarged eight times Power Transformers 76 * 40 270v * 2 6.3v 3.15v * 2 Size: 29*17*5CM Weight: 3.8 kg Best Diy Tube Amp
Features: FE-6J1-2 fever tube pre-amp board is the circuit schematic design imitation crew Music fax X-10D, to be rational optimization, more stable performance than the original machine, tube play 10% increase. Using a single 12V AC input, comes with boost function, low supply voltage to the effect of high-pressure tube. The capacitance filter of 8 470UFs is very clean. Excellent power supply system to ensure that the four 470UF capacitor filter clean, tube filament is connected in series, DC 12V power supply, reducing noise. Using MET series of non-polar capacitor, high-frequency low-resistance electrolytic capacitors, 1% precision metal film resistors, J-class military regulation tube 6J1. Specification: Model: 6jl electronic tube bile preamplifier, can replace the tube type 6AK5, 565... [Read More] Best Diy Tube Amp
Features : 100%Brand New and High Quality. Excellent sound effects. Unique appearance. Easy to install. Provide full music enjoyment to the post-amplifier. More stable performance than the original machine. Specifications : Models: 6J1 tube Channel types: 2.0 / stereo Working voltage: AC12V 0.8 A The power interface: 5.5 * 2.5 plug Circuit board size: 77 x 75 x 52 mm Potentiometer role: volume adjustment + power switch. Package Included : 1 × 6J1 Tube Pre-amplifier Board DIY Kits. Best Diy Tube Amp
Why us? The Nobsound NS-02E designed by Douk Audio Studio is a powerful Hi-Fi headphone amp. It has an anodized aluminum chassis with a replacable vacuum tube shining blue illumination on the top. The Nobsound NS-02E can provide soft and warm sound while maintaining its exceptional clarity. Most importantly, the affordable price makes both Hi-Fi freshmen and Hi-Fi veterans can enjoy it. And that's exactly one of our targets. The Nobsound NS-02E can be paired with your preamp, smart phone, computer, iPod, stereo system, and other audio device as well as your favorite headphones. It can easily power high-performance headphones including the HD 580, HD 600, K 701, K 702, Q 701, DT880, T70, T90, SR225, SR325, RS1e. It will also be a good match for active speaker systems. The Nobsound NS-02E ca... [Read More] Best Diy Tube Amp
Introduction to Line:1, the input voltage amplifierThe circuit has a small distortion, low noise, wide frequency response characteristics, is one of common line of power amplifier circuit at present.2, the power output stagePower tube 6P3P standard connection, the signal from the control gate (⑤ feet) input, screen grid (④ feet) and power + B1 directly connected. This connection is characterized by: high amplification efficiency. To achieve the characteristics of the power amplifier tube table provided by the output power. R6 is the output stage cathode resistance, the output stage gate negative pressure determined at -19.5V. 6P3P screen voltage of 300V, Best Diy Tube Amp This product uses 6N1 lines constitute the input stagePower amplifier level 6P3P standard connection, 6P3P for the entry-level productsLine design is reasonable, well-produced, but also play to the realm of fever
Specifications:Size: 6x30mmMaterial: GlassVoltage: 250VAmpere Value: 10ADiameter: 6mmLength: 30mmPackage Included: 1 Box (100 Best Diy Tube Amp These fuses can provide overcurrent protection of an electrical circuit.A essential safety device of electrical engineering.They can be easily installed for replacing your old or damaged fuse.Perfect for the DIY projects with valued price.Size: 6x30mm; Voltage: 250V; Ampere Value:
Introduction to Line:1, the input voltage amplifierThe circuit has a small distortion, low noise, wide frequency response characteristics, is one of common line of power amplifier circuit at present.2, the power output stagePower tube 6P3P standard connection, the signal from the control gate (⑤ feet) input, screen grid (④ feet) and power + B1 directly connected. This connection is characterized by: high amplification efficiency. To achieve the characteristics of the power amplifier tube table provided by the output power. R6 is the output stage cathode resistance, the output stage gate negative pressure determined at -19.5V. 6P3P screen voltage of 300V, Best Diy Tube Amp This product uses 6N1 lines constitute the input stagePower amplifier level 6P3P standard connection, 6P3P for the entry-level productsLine design is reasonable, well-produced, but also play to the realm of fever
Specifications:Name: 6J1 Valve Tube Preamplifier Board DIY KitsModel: 6j1 tube (can replace the model 6AK5, 6AU6,5654, etc.)Channel type: 2.0 / StereoWorking voltage: AC12V 0.8A or abovePower connector: 5.5 x 2.5 plugBoard Dimensions: Width 77mm x Depth 75mm x Height 57mmFeatures:1.AC 12V input: DC5.5 * 2.1 socket, with AC 12V transformer, if you want to use plug-free AC 12V transformer, you need to wire the power cord soldered on the circuit board. Remember: can not use DC power input, otherwise it does not work!2.Channel input: for the audio signal input, you can connect the phone, computer, M3, MP4, and other music Best Diy Tube Amp Model: 6j1 tube (can replace the model 6AK5, 6AU6,5654, etc.)Channel type: 2.0 / StereoWorking voltage: AC12V 0.8A or abovePower connector: 5.5 x 2.5 plugBoard Dimensions: Width 77mm x Depth 75mm x Height
Specifications:Name: 6J1 Valve Tube Preamplifier Board DIY KitsModel: 6j1 tube (can replace the model 6AK5, 6AU6,5654, etc.)Channel type: 2.0 / StereoWorking voltage: AC12V 0.8A or abovePower connector: 5.5 x 2.5 plugBoard Dimensions: Width 77mm x Depth 75mm x Height 57mmFeatures:1.AC 12V input: DC5.5 * 2.1 socket, with AC 12V transformer, if you want to use plug-free AC 12V transformer, you need to wire the power cord soldered on the circuit board. Remember: can not use DC power input, otherwise it does not work!2.Channel input: for the audio signal input, you can connect the phone, computer, M3, MP4, and other music Best Diy Tube Amp Model: 6j1 tube (can replace the model 6AK5, 6AU6,5654, etc.)Channel type: 2.0 / StereoWorking voltage: AC12V 0.8A or abovePower connector: 5.5 x 2.5 plugBoard Dimensions: Width 77mm x Depth 75mm x Height
This is a build of a simple but otherwise excellent tube amplifier. The unit is based on PCL82 - 16A8 Tubes (Valves), it's single ended and stereo and sounds amazing. Construction is made easier by... PCL82,ECL82,Tube,Valve,Amplifier,Build,HiFi,Audio,Boost Convert,Small,Compact,16A8,Easy Construction
DIY AMP! The Millet "Starving Student" which can be built for under $120 Discord: https://discordapp.com/invite/hgYsgA7 Patreon: https://www.patreon.com/user?u=4776882 http://www.pmillett.com/st... tube,amp,cheap,$120,audio,hifi,hi,fi,hi-fi,starving,student,millet,headphone,headphones,amplifier...
At the beginning of the year, I found this interesting scheme of tube amplifiers on a forum and decided to make it. After design of layout I ordered the necessary parts. In the meanwhile, looking f... diy,tube,KT88,EL34,ECC85,Abdellah,Gendrano,Kegger,amplifier,pojačalo,cijevno,Blueglow
© 10Bestify.com - all rights reserved - Sitemap 10Bestify.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com