TOP 10 Best Diy Tube Amp Kit Results at 10Bestify.com

  • Nobsound EL34 Class A Single-ended Tube Amplifier Stereo HiFi Amp DIY Kit 1Set

    Parameters: With original and new tubes 6n9p+EL34B Input Impedance: 100Kohm Output Impedance:4ohm 8ohm Signal to Noise Ratio: 89dB Input Sensitivity: 500--2000mV Input :110V/ 220V Output power:13w+13w (RMS) Frequeney responses: 20Hz--30KHz+/-1dB Supply Votage: all voltages are available 60Hz/50Hz Total Hamonic Distortion: less than 1%(1KHz) Tubes Included: 2pcs EL34B, 2pc 6N9P, 1pc 5Z3P Maximum input peak:500mW Dimension:350(W)*50(H)*170(D)mm Weight: 9.5kg With 2 new original BENNIC 0.33UF630V Capacitor, 2 ELNA 220UF/63V Resistor Notice: The loading resistor of this product is 4 ohm /8 ohm. Please do not change the value. Otherwise, the 6P3 loading resistance will be changed too. Please don't cut off the loading when it's working. If you want to connect this amplfier with a preamplifi... [Read More]
    Best Diy Tube Amp Kit

    • ASIN: B01N656K6S
    • ASIN: B01N656K6S
    • Brand: Nobsound
    • Manufacturer: Nobsound

  • Phoncoo DIY Kit AC 12V 6J1 Tube Fever Pre Amplifier Preamp AMP Pre-Amplifier Board Headphone Buffer Module Stereo Potentiometer Valve

    The item is New and with good quality.We will test it before shipment. Type:Voltage RegulatorWeight:0.101kg (0.22lb.)
    Best Diy Tube Amp Kit

    • ASIN: B07JH43NPV
    • ASIN: B07JH43NPV
    • Brand: Phoncoo
    • Manufacturer: Phoncoo

  • Nobsound 6N8P+6P3P HIFI Single-Ended Pure Class A Tube Amp Vacuum Power Amplifier DIY Kit

    Item specifics: Tubes: 5Z4P / 5U4C * 1 + 6N8P / 6H8C * 2 + 6P3P / 6L6GC * 2 Power supply: 300v * 2 6.3v 5v 3.15v * 2 Signal / Noise Ratio: 95dB Distortion: less than 1% at full power Frequency: 10HZ-70KHZ 3dB Output Power: 7W +7 W Voltage: 100V-240V Size: 290 * 170 * 150 mm Weight: 8KG
    Best Diy Tube Amp Kit

    • ASIN: B01MA2XASK
    • ASIN: B01MA2XASK
    • Brand: Nobsound
    • Manufacturer: Nobsound

  • Elegoo EL-KIT-008 Mega 2560 Project The Most Complete Ultimate Starter Kit w/Tutorial for Arduino UNO Nano

    Established in 2011, ELEGOO is a thriving technology company dedicated to open-source hardware research & development, production and marketing. Our own Quality Management Team will secure the premium quality of our products and we would like to receive your valuable suggestions for our products and make your idea come true component listing: 1pcs Mega 2560 Controller Board 1pcs USB Cable 1pcs Breadboard 1pcs 65 Jumper Wire 1pcs IC 74HC595 1pcs Active Buzzer 1pcs Tilt Switch 1pcs Photo resistor 5pcs Yellow LED 5pcs Blue LED 5pcs Green LED 5pcs Red LED 1pcs RGB LED 5pcs Button (small) 10pcs Resistor (10R) 10pcs Resistor (100R) 10pcs Resistor (220R) 10pcs Resistor (330R) 10pcs Resistor (1K) 10pcs Resistor (2K) 10pcs Resistor (5K1) 10pcs Resistor (10K) 10pcs Resistor (100K) 10pcs Resistor (1M... [Read More]
    Best Diy Tube Amp Kit

    • ASIN: B01EWNUUUA
    • UPC: 746591610586
    • ASIN: B01EWNUUUA
    • Brand: ELEGOO
    • Manufacturer: ELEGOO

  • 12V DIY Preamplifier Kit 6J1 Preamp Tube Board Preamplifier 3.5MM Headphone Amplifier Replacement

    Description: This is a preamplifier + headphone amplifier that can be used with a post-amplifier or an active speaker, or it can be used with headphones. The sound of this board is warm, mellow, sweet and transparent, and full of music. It is a cost-effective preamplifier. Replaceable op amp and upgrade the tube, just plug it in the direction of the foot. Let you enjoy DIY fun! Specification: Material: acrylic Input port: audio input, power input Output port: 3.5MM headphone output, preamp output Size: 12.5 x 7.6 x 3.5cm / 4.9 x 3.0 x 1.4in (assembled size)  Weight: approx. 259g Packing List: 1 x Acrylic Board 1 x 6J1-2 Tube Board
    Best Diy Tube Amp Kit

    • ASIN: B07LFFHZHF
    • UPC: 736077508650
    • ASIN: B07LFFHZHF
    • Brand: Zerone
    • Manufacturer: Zerone

  • Elenco AM/FM Radio Kit |Switch Between ICs & Transistors | Lead Free Solder | Great STEM Project | Superheterodyne Designed to AM and FM Broadcasts | SOLDERING REQUIRED

    Learn about AM and FM radio technology and the the functional components used in creating AM-FM receivers and amplifiers. 56 page training course is divided into 9 lessons; Audio Amplifier, AM Detector, AM IF, AM Amplifier, AM Mixer & Oscillator, FM Detector, 1st FM IF, 2nd FM IF, FM RF Stages. “Superheterodyne” designed to receive standard AM and FM broadcast frequencies. New transistor module allows you to switch between the modern integrated circuit (IC) technology and the original transistor technology. Includes radio mounting stand. PLEASE NOTE: The AM/FM Radio project is divided into two parts, the AM Radio Section and the FM Radio Section. Initially, only identify the parts that you will need for the AM radio as listed in the manual. DO NOT OPEN the bags listed for the FM radio.... [Read More]
    Best Diy Tube Amp Kit

    • ASIN: B008515U1U
    • UPC: 756619008769
    • ASIN: B008515U1U
    • Brand: Elenco
    • Manufacturer: Elenco Electronics Inc

  • Northbear AC 12V 6J1 Valve Pre-amp Tube PreAmplifier Board Headphone Buffer DIY KIT (DIY Kits)

    Instructions: 1, AC 12V input: Using DC5.5 * 2.1 socket, 12V AC power adapter is available, you can also use 12V AC transformer, if you use 12V AC transformer, power lines need to solder on the circuit board. Remember: You can not use a DC power input, otherwise it does not work! 2, the left-channel input / right channel input: Audio signal input, can be connected to mobile phones, computers, M3, MP4, and other music players. 3, the output of the left channel / right channel output: The audio signal output terminal can be connected to the audio signal input amplifier, power amplifier boards, to provide post-amp Bile flavor of music to enjoy! 4, the power switch / volume knob: The knob counter-clockwise to decrease the volume beginning, when the volume down to the minimum, if it continues t... [Read More]
    Best Diy Tube Amp Kit

    • ASIN: B074X5YP85
    • UPC: 736561415280
    • ASIN: B074X5YP85
    • Brand: Northbear
    • Manufacturer: Northbear

  • Nobsound EL34 Pure Vacuum Tube Amplifier Single-Ended Class A HiFi Stereo Power Amp 12W+12W (DIY Kit)

    Diagram:https://drive.google.com/open?id=1HnZELnau3EPR0Gk-wUPoxipQ0_PF7oalShipping date: This item will be shipped by UPS from China, which usually take 4~7 days to arrive. Parameters: Type: Single-Ended Class A Input Voltage: 110V-120V / 50-60Hz Output Power: 12W* 2 (ultra-linear connection) Frequency Response: 20Hz - 28KHz Output impedance: 4,8Ω SNR: 88dB Total Harmonic Distortion: ≤ 1% (1kHz) Input Sensitivity: 750MV Input impedance: 100KΩ (two input signals) Audio input: 2× Stereo L/R RCA Audio output: 1× Banana Speaker Jacks Dimensions(W × D × H): 310 × 268 × 165mm Weight: About 11Kg(You can see the quality from its heavy weight) Package includes: 1× full set of amp kit 1× power cord
    Best Diy Tube Amp Kit

    • ASIN: B0757LH67R
    • ASIN: B0757LH67R
    • Brand: Nobsound
    • Manufacturer: Nobsound

  • Nobsound 6J4+6P6P Vacuum Tube Pre-Amplifier Stereo HiFi Preamp DIY Kit 1Set

    Technical parameters: Frequeney responses: 10Hz-100KHz (± 0dB), 10Hz-200KHz (± 0.2dB) RMS: 0.8W * 2 Power supply: AC 220V-240V or 110V Tubes used: 2pcs 6P6P, 2pcs 6J4, 1pc 653P Input: 4ways RCA jacks Output: 1way RCA jacks Supply votage: All Voltages are available 60Hz / 50Hz The machine output voltage of 12V, an enlarged eight times Power Transformers 76 * 40 270v * 2 6.3v 3.15v * 2 Size: 29*17*5CM Weight: 3.8 kg
    Best Diy Tube Amp Kit

    • ASIN: B01N656HHD
    • ASIN: B01N656HHD
    • Brand: Nobsound
    • Manufacturer: Nobsound

  • Binney & Smith Crayola(R) Drawing Chalk, Assorted Colors, Box Of 24

    Crayola Colored Drawing Chalk features strong, brilliant colors that lend themselves to dramatically colorful effects on non-glossy papers in various techniques, such as dry-chalk, wet chalk painting and stenciling. Non-Toxic chalk in assorted colors is sold as 24 per pack.
    Best Diy Tube Amp Kit

    • ASIN: B00006IBOJ
    • UPC: 716620040400
    • ASIN: B00006IBOJ
    • Brand: Crayola
    • Manufacturer: Crayola

  • 6N1+6P3P Tube Amplifier DIY Kit Class A Single-end tube Power Amp Amplifier

    Introduction to Line:1, the input voltage amplifierThe circuit has a small distortion, low noise, wide frequency response characteristics, is one of common line of power amplifier circuit at present.2, the power output stagePower tube 6P3P standard connection, the signal from the control gate (⑤ feet) input, screen grid (④ feet) and power + B1 directly connected. This connection is characterized by: high amplification efficiency. To achieve the characteristics of the power amplifier tube table provided by the output power. R6 is the output stage cathode resistance, the output stage gate negative pressure determined at -19.5V. 6P3P screen voltage of 300V,
    Best Diy Tube Amp Kit
    This product uses 6N1 lines constitute the input stagePower amplifier level 6P3P standard connection, 6P3P for the entry-level productsLine design is reasonable, well-produced, but also play to the realm of fever

    • UPC: 160088719

  • 6N1+6P3P Tube Amplifier DIY Kit Class A Single-end tube Power Amp Amplifier

    Introduction to Line:1, the input voltage amplifierThe circuit has a small distortion, low noise, wide frequency response characteristics, is one of common line of power amplifier circuit at present.2, the power output stagePower tube 6P3P standard connection, the signal from the control gate (⑤ feet) input, screen grid (④ feet) and power + B1 directly connected. This connection is characterized by: high amplification efficiency. To achieve the characteristics of the power amplifier tube table provided by the output power. R6 is the output stage cathode resistance, the output stage gate negative pressure determined at -19.5V. 6P3P screen voltage of 300V,
    Best Diy Tube Amp Kit
    This product uses 6N1 lines constitute the input stagePower amplifier level 6P3P standard connection, 6P3P for the entry-level productsLine design is reasonable, well-produced, but also play to the realm of fever

    • UPC: 183421360
    • Rating: 3.0

  • 6J1 Valve Tube Preamplifier Board Bass on Musical Fidelity DIY HiFi Tube Amp Kits X10-D & Case

    Specifications:Name: 6J1 Valve Tube Preamplifier Board DIY KitsModel: 6j1 tube (can replace the model 6AK5, 6AU6,5654, etc.)Channel type: 2.0 / StereoWorking voltage: AC12V 0.8A or abovePower connector: 5.5 x 2.5 plugBoard Dimensions: Width 77mm x Depth 75mm x Height 57mmFeatures:1.AC 12V input: DC5.5 * 2.1 socket, with AC 12V transformer, if you want to use plug-free AC 12V transformer, you need to wire the power cord soldered on the circuit board. Remember: can not use DC power input, otherwise it does not work!2.Channel input: for the audio signal input, you can connect the phone, computer, M3, MP4, and other music
    Best Diy Tube Amp Kit
    Model: 6j1 tube (can replace the model 6AK5, 6AU6,5654, etc.)Channel type: 2.0 / StereoWorking voltage: AC12V 0.8A or abovePower connector: 5.5 x 2.5 plugBoard Dimensions: Width 77mm x Depth 75mm x Height

    • UPC: 529344082

  • 6J1 Valve Tube Preamplifier Board Bass on Musical Fidelity DIY HiFi Tube Amp Kits X10-D & Case

    Specifications:Name: 6J1 Valve Tube Preamplifier Board DIY KitsModel: 6j1 tube (can replace the model 6AK5, 6AU6,5654, etc.)Channel type: 2.0 / StereoWorking voltage: AC12V 0.8A or abovePower connector: 5.5 x 2.5 plugBoard Dimensions: Width 77mm x Depth 75mm x Height 57mmFeatures:1.AC 12V input: DC5.5 * 2.1 socket, with AC 12V transformer, if you want to use plug-free AC 12V transformer, you need to wire the power cord soldered on the circuit board. Remember: can not use DC power input, otherwise it does not work!2.Channel input: for the audio signal input, you can connect the phone, computer, M3, MP4, and other music
    Best Diy Tube Amp Kit
    Model: 6j1 tube (can replace the model 6AK5, 6AU6,5654, etc.)Channel type: 2.0 / StereoWorking voltage: AC12V 0.8A or abovePower connector: 5.5 x 2.5 plugBoard Dimensions: Width 77mm x Depth 75mm x Height

    • UPC: 636728199

  • 6N1+6P3P Amplifier HiFi Class A Tube Audio Vacuum Power Amp DIY Single Ended Kit

    Introduction to Line:1, the input voltage amplifierThe circuit has a small distortion, low noise, wide frequency response characteristics, is one of common line of power amplifier circuit at present.2, the power output stagePower tube 6P3P standard connection, the signal from the control gate (⑤ feet) input, screen grid (④ feet) and power + B1 directly connected. This connection is characterized by: high amplification efficiency. To achieve the characteristics of the power amplifier tube table provided by the output power. R6 is the output stage cathode resistance, the output stage gate negative pressure determined at -19.5V. 6P3P screen voltage of 300V,
    Best Diy Tube Amp Kit
    This product uses 6N1 lines constitute the input stagePower amplifier level 6P3P standard connection, 6P3P for the entry-level productsLine design is reasonable, well-produced, but also play to the realm of fever

    • UPC: 672622994

  • Kit Amp Vs Original Marshall

    Marshall 1987X 50W Plexi Reissue is Compared to a Tube Amp Doctor kit (JTM45 mostly converted to 1987, diod rectifier, split V1 cathode etc, the extra tube is used for the effects loop). Guitar 200...
    Kit amp,Kit guitar amp,Marshall kit,Johan Segeborn,Tube depot,Mojotone,Tube amp doctor,Amp kits,M...

    How To Build a Mojotone 5E3 Tweed Deluxe Style Amp Kit Build- Walkthrough

    In this video we walk you through the complete build process of building the Mojotone 5E3 Tweed Deluxe Style Kit. For more info, please also check out our Make it Monday Articles here: http://ww...
    mojotone,tweed deluxe,fender amp,build,diy,walkthrough

    Build you own TUBE AMP!!! (KLD DIY 15w tube amp kit REVIEW + DEMO)

    This is the unboxing, building, review, and demo of the KLD Pilot15 15w tube amp DIY kit available on eBay! This kit was actually very easy to build, and includes everything you need except for th...
    DIY amp,tube amp kit,diy amp kit,build your own guitar amp,guitar amp kit,diy guitar amp,how to b...